[PVE-User] Proxmox 5 (LACP/Bridge/VLAN120)

[Uwe Sauter]

Sorry, I mixed up the IP addresses. MTU according to what you switch supports (in this case jumbo frames with 9000 bytes).

/etc/network/interfaces
-----------------------------------------
# management interface
auto eth0
iface eth0 inet static
  address 192.168.0.2
  netmask 255.255.255.0
  gateway 192.168.0.254

# 1st interface in bond
auto eth1
iface eth1 inet manual
  mtu 9000

# 2nd interface in bond
auto eth2
iface eth2 inet manual
  mtu 9000

# bond
auto bond0
iface bond0 inet manual
  slaves eth1 eth2
  bond-mode 802.3ad
  bond-miimon 100
  mtu 9000

# interface for vlan 120 on bond with IP
auto bond0.120
iface bond0.120 inet static
  address 10.100.100.8
  netmask 255.255.255.0
  mtu 9000

# interface for vlan 130 on bond without IP (just for VMs)
auto bond0.130
iface bond0.130 inet manual

-----------------------------------------


Am 23.08.2017 um 07:27 schrieb Uwe Sauter:
> An example out of my head:
> 
> 
> /etc/network/interfaces
> -----------------------------------------
> # management interface
> auto eth0
> iface eth0 inet static
>   address 10.100.100.8
>   netmask 255.255.255.0
>   gateway 10.100.100.254
> 
> # 1st interface in bond
> auto eth1
> iface eth1 inet manual
>   mtu 9000
> 
> # 2nd interface in bond
> auto eth2
> iface eth2 inet manual
>   mtu 9000
> 
> # bond
> auto bond0
> iface bond0 inet manual
>   slaves eth1 eth2
>   bond-mode 802.3ad
>   bond-miimon 100
>   mtu 9000
> 
> # interface for vlan 120 on bond with IP
> auto bond0.120
> iface bond0.120 inet static
>   address 192.168.123.2
>   netmask 255.255.255.0
>   mtu 9000
> 
> # interface for vlan 130 on bond without IP (just for VMs)
> auto bond0.130
> iface bond0.130 inet manual
> 
> -----------------------------------------
> 
> 
> Am 23.08.2017 um 06:44 schrieb Alexandre DERUMIER:
>> Hi,
>>
>> you can create a bond0.120 interface and setup ip on it.
>>
>> (and keep bond0 in bridge).
>>
>>
>> another way, enable "vlan aware" option in bridge. (see gui),
>>
>> then you can create a
>>
>> vmbr0.120, and setup ip on it.
>>
>>
>> ----- Mail original -----
>> De: "Devin Acosta" <devin at pabstatencio.com>
>> À: "proxmoxve" <pve-user at pve.proxmox.com>
>> Envoyé: Mercredi 23 Août 2017 03:40:07
>> Objet: [PVE-User] Proxmox 5 (LACP/Bridge/VLAN120)
>>
>> I need to configure Proxmox 5.x with the following. 
>>
>> Bond of 2 interfaces using LACP 
>> Bridge off Bond0, with IP on VLAN 120 (10.100.100.8/24) 
>> The network switch doesn’t have native VLAN, so the IP has to be on the 
>> TAGGED VLAN 120. 
>>
>> Please help. ;) 
>>
>> Devin 
>> _______________________________________________ 
>> pve-user mailing list 
>> pve-user at pve.proxmox.com 
>> https://pve.proxmox.com/cgi-bin/mailman/listinfo/pve-user 
>>
>> _______________________________________________
>> pve-user mailing list
>> pve-user at pve.proxmox.com
>> https://pve.proxmox.com/cgi-bin/mailman/listinfo/pve-user
>>
>