[PVE-User] PVE 7 & LACP

Gilberto Ferreira gilberto.nunes32 at gmail.com
Wed Jul 21 17:45:32 CEST 2021


Perhaps you need to change or add this feature in the network interface
file:

https://pve.proxmox.com/wiki/Upgrade_from_6.x_to_7.0#Linux_Bridge_MAC-Address_Change



---
Gilberto Nunes Ferreira
(47) 99676-7530 - Whatsapp / Telegram






Em qua., 21 de jul. de 2021 às 12:18, Uwe Sauter <uwe.sauter.de at gmail.com>
escreveu:

> Hi all,
>
> Fresh installation of PVE 7 with all available updates.
>
> It looks like I'm unable to configure bonding of two interfaces using LCAP.
>
> Output from "ip a":
> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
> default qlen 1000
>     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
>     inet 127.0.0.1/8 scope host lo
>        valid_lft forever preferred_lft forever
>     inet6 ::1/128 scope host
>        valid_lft forever preferred_lft forever
> 2: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master
> vmbr1224 state UP group default
> qlen 1000
>     link/ether a4:bf:01:2f:63:f2 brd ff:ff:ff:ff:ff:ff
>     altname enp24s0f0
> 3: enp59s0f4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc mq state UP
> group default qlen 1000
>     link/ether 00:07:43:18:82:70 brd ff:ff:ff:ff:ff:ff
>     inet6 fe80::207:43ff:fe18:8270/64 scope link
>        valid_lft forever preferred_lft forever
> 4: enp59s0f4d1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc mq state
> UP group default qlen 1000
>     link/ether 00:07:43:18:82:78 brd ff:ff:ff:ff:ff:ff
>     inet6 fe80::207:43ff:fe18:8278/64 scope link
>        valid_lft forever preferred_lft forever
> 5: eno2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group
> default qlen 1000
>     link/ether a4:bf:01:2f:63:f3 brd ff:ff:ff:ff:ff:ff
>     altname enp24s0f1
> 6: ibp94s0: <BROADCAST,MULTICAST> mtu 2044 qdisc noop state DOWN group
> default qlen 256
>     link/infiniband
> 80:00:0a:08:fe:80:00:00:00:00:00:00:f4:52:14:03:00:2c:14:51 brd
> 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
> 7: ibp94s0d1: <BROADCAST,MULTICAST> mtu 2044 qdisc noop state DOWN group
> default qlen 256
>     link/infiniband
> 80:00:0a:09:fe:80:00:00:00:00:00:00:f4:52:14:03:00:2c:14:52 brd
> 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
> 8: vmbr1224: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue
> state UP group default qlen 1000
>     link/ether a4:bf:01:2f:63:f2 brd ff:ff:ff:ff:ff:ff
>     inet 10.224.203.1/16 scope global vmbr1224
>        valid_lft forever preferred_lft forever
>     inet6 fe80::a6bf:1ff:fe2f:63f2/64 scope link
>        valid_lft forever preferred_lft forever
>
>
> My current /etc/network/interfaces, which is missing the bridges for the
> VMs:
> auto lo
> iface lo inet loopback
>
> auto eno1
> iface eno1 inet manual
>
> auto enp59s0f4
> iface enp59s0f4 inet manual
>   mtu 9000
>
> auto enp59s0f4d1
> iface enp59s0f4d1 inet manual
>   mtu 9000
>
> auto bond0
> iface bond0 inet manual
>   slaves enp59s0f4 enp59s0f4d1
>   bond-downdelay 200
>   bond-miimon 100
>   bond-mode 802.3ad
>   bond-updelay 200
>
> auto vmbr1224
> iface vmbr1224 inet static
>   address 10.224.203.1
>   netmask 255.255.0.0
>   gateway 10.224.200.1
>   bridge_ports eno1
>   bridge_stp off
>   bridge_fd 0
>
> ##  # VLAN 155 nativ on bond0
> ##  auto vmbr155
> ##  iface vmbr155 inet manual
> ##    mtu 9000
> ##    bridge_ports bond0
> ##    bridge_stp off
> ##    bridge_fd 0
>
>
> This config was copied over from the PVE 6 installation on the same host
> which experienced a SSD
> failure and thus was re-installed with PVE 7.
>
>
> Am I missing something? Am I being blind?
>
>
> Any help is appreciated.
>
>
> Thanks,
>
>         Uwe
>
>
>
>
> _______________________________________________
> pve-user mailing list
> pve-user at lists.proxmox.com
> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
>
>


More information about the pve-user mailing list