[PVE-User] PVE 7 & LACP

alexandre derumier aderumier at odiso.com
Wed Jul 21 19:58:23 CEST 2021


slaves enp59s0f4 enp59s0f4d1

---->

bond-slaves enp59s0f4 enp59s0f4d1


("slaves" is deprecated since years, and ifupdown2 don't support it)


Le mercredi 21 juillet 2021 à 19:31 +0200, Uwe Sauter a écrit :
> No, the bond isn't created on system boot. Thus the bridge that
> should connect the bond with the VMs
> is created but the connection is not made.
> 
> 
> Am 21.07.21 um 18:41 schrieb Gilberto Ferreira:
> > So did you solve the issue?
> > ---
> > Gilberto Nunes Ferreira
> > (47) 99676-7530 - Whatsapp / Telegram
> > 
> > 
> > 
> > 
> > 
> > 
> > Em qua., 21 de jul. de 2021 às 12:49, Uwe Sauter
> > <uwe.sauter.de at gmail.com
> > <mailto:uwe.sauter.de at gmail.com>> escreveu:
> > 
> >     Hi Gilberto,
> > 
> >     thanks for that tip. Unfortunately the network configuration
> > quits a few steps before the bridge is
> >     configured. The needed bond0 is not created…
> > 
> > 
> >     Regards,
> > 
> >             Uwe
> > 
> > 
> >     Am 21.07.21 um 17:45 schrieb Gilberto Ferreira:
> >     > Perhaps you need to change or add this feature in the network
> > interface file:
> >     >
> >     >
> > https://pve.proxmox.com/wiki/Upgrade_from_6.x_to_7.0#Linux_Bridge_MAC-Address_Change
> >    
> > <https://pve.proxmox.com/wiki/Upgrade_from_6.x_to_7.0#Linux_Bridge_MAC-Address_Change
> > >
> >     >
> > <https://pve.proxmox.com/wiki/Upgrade_from_6.x_to_7.0#Linux_Bridge_MAC-Address_Change
> >    
> > <https://pve.proxmox.com/wiki/Upgrade_from_6.x_to_7.0#Linux_Bridge_MAC-Address_Change
> > >>
> >     >
> >     >
> >     >
> >     > ---
> >     > Gilberto Nunes Ferreira
> >     > (47) 99676-7530 - Whatsapp / Telegram
> >     >
> >     >
> >     >
> >     >
> >     >
> >     >
> >     > Em qua., 21 de jul. de 2021 às 12:18, Uwe Sauter
> > <uwe.sauter.de at gmail.com
> >     <mailto:uwe.sauter.de at gmail.com>
> >     >
> > <mailto:uwe.sauter.de at gmail.com <mailto:uwe.sauter.de at gmail.com>>>
> > escreveu:
> >     >
> >     >     Hi all,
> >     >
> >     >     Fresh installation of PVE 7 with all available updates.
> >     >
> >     >     It looks like I'm unable to configure bonding of two
> > interfaces using LCAP.
> >     >
> >     >     Output from "ip a":
> >     >     1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue
> > state UNKNOWN group default qlen 1000
> >     >         link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> >     >         inet 127.0.0.1/8 <http://127.0.0.1/8>
> > <http://127.0.0.1/8 <http://127.0.0.1/8>> scope
> >     host lo
> >     >            valid_lft forever preferred_lft forever
> >     >         inet6 ::1/128 scope host
> >     >            valid_lft forever preferred_lft forever
> >     >     2: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc
> > mq master vmbr1224 state UP
> >     group default
> >     >     qlen 1000
> >     >         link/ether a4:bf:01:2f:63:f2 brd ff:ff:ff:ff:ff:ff
> >     >         altname enp24s0f0
> >     >     3: enp59s0f4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000
> > qdisc mq state UP group default
> >     qlen 1000
> >     >         link/ether 00:07:43:18:82:70 brd ff:ff:ff:ff:ff:ff
> >     >         inet6 fe80::207:43ff:fe18:8270/64 scope link
> >     >            valid_lft forever preferred_lft forever
> >     >     4: enp59s0f4d1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu
> > 9000 qdisc mq state UP group default
> >     qlen 1000
> >     >         link/ether 00:07:43:18:82:78 brd ff:ff:ff:ff:ff:ff
> >     >         inet6 fe80::207:43ff:fe18:8278/64 scope link
> >     >            valid_lft forever preferred_lft forever
> >     >     5: eno2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state
> > DOWN group default qlen 1000
> >     >         link/ether a4:bf:01:2f:63:f3 brd ff:ff:ff:ff:ff:ff
> >     >         altname enp24s0f1
> >     >     6: ibp94s0: <BROADCAST,MULTICAST> mtu 2044 qdisc noop
> > state DOWN group default qlen 256
> >     >         link/infiniband
> > 80:00:0a:08:fe:80:00:00:00:00:00:00:f4:52:14:03:00:2c:14:51 brd
> >     >   
> >  00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
> >     >     7: ibp94s0d1: <BROADCAST,MULTICAST> mtu 2044 qdisc noop
> > state DOWN group default qlen 256
> >     >         link/infiniband
> > 80:00:0a:09:fe:80:00:00:00:00:00:00:f4:52:14:03:00:2c:14:52 brd
> >     >   
> >  00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
> >     >     8: vmbr1224: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
> > qdisc noqueue state UP group default
> >     >     qlen 1000
> >     >         link/ether a4:bf:01:2f:63:f2 brd ff:ff:ff:ff:ff:ff
> >     >         inet 10.224.203.1/16 <http://10.224.203.1/16>
> > <http://10.224.203.1/16
> >     <http://10.224.203.1/16>> scope global vmbr1224
> >     >            valid_lft forever preferred_lft forever
> >     >         inet6 fe80::a6bf:1ff:fe2f:63f2/64 scope link
> >     >            valid_lft forever preferred_lft forever
> >     >
> >     >
> >     >     My current /etc/network/interfaces, which is missing the
> > bridges for the VMs:
> >     >     auto lo
> >     >     iface lo inet loopback
> >     >
> >     >     auto eno1
> >     >     iface eno1 inet manual
> >     >
> >     >     auto enp59s0f4
> >     >     iface enp59s0f4 inet manual
> >     >       mtu 9000
> >     >
> >     >     auto enp59s0f4d1
> >     >     iface enp59s0f4d1 inet manual
> >     >       mtu 9000
> >     >
> >     >     auto bond0
> >     >     iface bond0 inet manual
> >     >       slaves enp59s0f4 enp59s0f4d1
> >     >       bond-downdelay 200
> >     >       bond-miimon 100
> >     >       bond-mode 802.3ad
> >     >       bond-updelay 200
> >     >
> >     >     auto vmbr1224
> >     >     iface vmbr1224 inet static
> >     >       address 10.224.203.1
> >     >       netmask 255.255.0.0
> >     >       gateway 10.224.200.1
> >     >       bridge_ports eno1
> >     >       bridge_stp off
> >     >       bridge_fd 0
> >     >
> >     >     ##  # VLAN 155 nativ on bond0
> >     >     ##  auto vmbr155
> >     >     ##  iface vmbr155 inet manual
> >     >     ##    mtu 9000
> >     >     ##    bridge_ports bond0
> >     >     ##    bridge_stp off
> >     >     ##    bridge_fd 0
> >     >
> >     >
> >     >     This config was copied over from the PVE 6 installation
> > on the same host which experienced
> >     a SSD
> >     >     failure and thus was re-installed with PVE 7.
> >     >
> >     >
> >     >     Am I missing something? Am I being blind?
> >     >
> >     >
> >     >     Any help is appreciated.
> >     >
> >     >
> >     >     Thanks,
> >     >
> >     >             Uwe
> >     >
> >     >
> >     >
> >     >
> >     >     _______________________________________________
> >     >     pve-user mailing list
> >     >   
> >  pve-user at lists.proxmox.com <mailto:pve-user at lists.proxmox.com>
> >    
> > <mailto:pve-user at lists.proxmox.com <mailto:pve-user at lists.proxmox.com
> > >>
> >     >   
> >  https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
> >     <https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user>
> >     >   
> >  <https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
> >     <https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user>>
> >     >
> > 
> 
> 
> _______________________________________________
> pve-user mailing list
> pve-user at lists.proxmox.com
> https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user




More information about the pve-user mailing list