[pve-devel] [PATCH docs v2 4/6] ceph: osd: revise and expand the section "Destroy OSDs"

[Alexander Zeidler]

Existing information is slightly modified and retained.

Add information:
* Mention and link to the sections "Troubleshooting" and "Replace OSDs"
* CLI commands (pveceph) must be executed on the affected node
* Check in advance the "Used (%)" of OSDs to avoid blocked I/O
* Check and wait until the OSD can be stopped safely
* Use `pveceph stop` instead of `systemctl stop ceph-osd@<ID>.service`
* Explain cleanup option a bit more

Signed-off-by: Alexander Zeidler <a.zeidler at proxmox.com>
---
v2:
* implement both suggestions from Max Carrara
** mention what the warning is about (unsafe to stop OSD yet)
** use WARNING admonition and adapt the point accordingly

 pveceph.adoc | 61 +++++++++++++++++++++++++++++-----------------------
 1 file changed, 34 insertions(+), 27 deletions(-)

diff --git a/pveceph.adoc b/pveceph.adoc
index 7401d2b..81a6cc7 100644
--- a/pveceph.adoc
+++ b/pveceph.adoc
@@ -502,33 +502,40 @@ ceph-volume lvm create --filestore --data /dev/sd[X] --journal /dev/sd[Y]
 Destroy OSDs
 ~~~~~~~~~~~~
 
-To remove an OSD via the GUI, first select a {PVE} node in the tree view and go
-to the **Ceph -> OSD** panel. Then select the OSD to destroy and click the **OUT**
-button. Once the OSD status has changed from `in` to `out`, click the **STOP**
-button. Finally, after the status has changed from `up` to `down`, select
-**Destroy** from the `More` drop-down menu.
-
-To remove an OSD via the CLI run the following commands.
-
-[source,bash]
-----
-ceph osd out <ID>
-systemctl stop ceph-osd@<ID>.service
-----
-
-NOTE: The first command instructs Ceph not to include the OSD in the data
-distribution. The second command stops the OSD service. Until this time, no
-data is lost.
-
-The following command destroys the OSD. Specify the '-cleanup' option to
-additionally destroy the partition table.
-
-[source,bash]
-----
-pveceph osd destroy <ID>
-----
-
-WARNING: The above command will destroy all data on the disk!
+If you experience problems with an OSD or its disk, try to
+xref:pve_ceph_mon_and_ts[troubleshoot] them first to decide if a
+xref:pve_ceph_osd_replace[replacement] is needed.
+
+To destroy an OSD:
+
+. Either open the web interface and select any {pve} node in the tree
+view, or open a shell on the node where the OSD to be deleted is
+located.
+
+. Go to the __Ceph -> OSD__ panel (`ceph osd df tree`). If the OSD to
+be deleted is still `up` and `in` (non-zero value at `AVAIL`), make
+sure that all OSDs have their `Used (%)` value well below the
+`nearfull_ratio` of default `85%`. In this way you can reduce the risk
+from the upcoming rebalancing, which may cause OSDs to run full and
+thereby blocking I/O on Ceph pools.
+
+. If the deletable OSD is not `out` yet, select the OSD and click on
+**Out** (`ceph osd out <id>`). This will exclude it from data
+distribution and starts a rebalance.
+
+. Click on **Stop**, if stopping is not safe yet, a warning will
+appear and you should click on **Cancel**, please try again shortly
+afterwards. When using the shell, check if it is safe to stop by
+reading the output from `ceph osd ok-to-stop <id>`, once true, run
+`pveceph stop --service osd.<id>` .
+
+. Finally:
++
+[WARNING]
+To remove the OSD from Ceph and delete all disk data, first click on
+**More -> Destroy**. Use the cleanup option to clean up the partition
+table and similar, enabling an immediate reuse of the disk in {pve}.
+Finally, click on **Remove** (`pveceph osd destroy <id> [--cleanup]`).
 
 
 [[pve_ceph_pools]]
-- 
2.39.5