[pve-devel] [PATCH docs 2/2] Refer to the bootloader chapter in remaining docs

[Stoiko Ivanov]

Editing the kernel commandline is described centrally in the bootloaders
chapter. Refer to it where appropriate (qm-pci-passthrough.adoc).

Additionally update the documentation on ZFS as rpool to the inclusion of
`systemd-boot`

Signed-off-by: Stoiko Ivanov <s.ivanov at proxmox.com>
---
 local-zfs.adoc          | 20 ++++++++++----------
 qm-pci-passthrough.adoc | 26 +++++++++++---------------
 2 files changed, 21 insertions(+), 25 deletions(-)

diff --git a/local-zfs.adoc b/local-zfs.adoc
index 13f6050..aae89e0 100644
--- a/local-zfs.adoc
+++ b/local-zfs.adoc
@@ -154,15 +154,9 @@ rpool/swap        4.25G  7.69T    64K  -
 Bootloader
 ~~~~~~~~~~
 
-The default ZFS disk partitioning scheme does not use the first 2048
-sectors. This gives enough room to install a GRUB boot partition. The
-{pve} installer automatically allocates that space, and installs the
-GRUB boot loader there. If you use a redundant RAID setup, it installs
-the boot loader on all disk required for booting. So you can boot
-even if some disks fail.
-
-NOTE: It is not possible to use ZFS as root file system with UEFI
-boot.
+Depending on whether the system is booted in EFI or legacy BIOS mode the
+{pve} installer sets up either `grub` or `systemd-boot` as main bootloader.
+See the chapter on  xref:system_booting[bootladers] for details.
 
 
 ZFS Administration
@@ -255,7 +249,13 @@ can be used as cache.
 
 .Changing a failed device
 
- zpool replace -f <pool> <old device> <new-device>
+ zpool replace -f <pool> <old device> <new device>
+
+.Changing a failed bootable device when using systemd-boot
+
+ sgdisk <healthy bootable device> -R <new device>
+ sgdisk -G <new device>
+ zpool replace -f <pool> <old zfs partition> <new zfs partition>
 
 
 Activate E-Mail Notification
diff --git a/qm-pci-passthrough.adoc b/qm-pci-passthrough.adoc
index 3895df4..a661848 100644
--- a/qm-pci-passthrough.adoc
+++ b/qm-pci-passthrough.adoc
@@ -45,9 +45,10 @@ some configuration to enable PCI(e) passthrough.
 
 .IOMMU
 
-The IOMMU has to be activated on the kernel commandline. The easiest way is to
-enable trough grub. Edit `'/etc/default/grub'' and add the following to the
-'GRUB_CMDLINE_LINUX_DEFAULT' variable:
+The IOMMU has to be activated on the
+xref:edit_kernel_cmdline[kernel commandline].
+
+The command line parameters are:
 
 * for Intel CPUs:
 +
@@ -60,12 +61,6 @@ enable trough grub. Edit `'/etc/default/grub'' and add the following to the
  amd_iommu=on
 ----
 
-[[qm_pci_passthrough_update_grub]]
-To bring this change in effect, make sure you run:
-
-----
-# update-grub
-----
 
 .Kernel Modules
 
@@ -87,6 +82,9 @@ After changing anything modules related, you need to refresh your
 # update-initramfs -u -k all
 ----
 
+If you are using `systemd-boot` for booting you additionally need to
+xref:systemd-boot-refresh[sync the new initramfs to the bootable partitions].
+
 .Finish Configuration
 
 Finally reboot to bring the changes into effect and check that it is indeed
@@ -316,10 +314,9 @@ Intels drivers for GVT-g are integrated in the Kernel and should work
 with 5th, 6th and 7th generation Intel Core Processors, as well as E3 v4, E3
 v5 and E3 v6 Xeon Processors.
 
-To enable it for Intel Graphcs, you have to make sure to load the module
-'kvmgt' (for example via `/etc/modules`) and to enable it on the Kernel
-commandline. For this you can edit `'/etc/default/grub'' and add the following
-to the 'GRUB_CMDLINE_LINUX_DEFAULT' variable:
+To enable it for Intel Graphics, you have to make sure to load the module
+'kvmgt' (for example via `/etc/modules`) and to enable it on the
+xref:edit_kernel_cmdline[Kernel commandline] and add the following parameter:
 
 ----
  i915.enable_gvt=1
@@ -327,8 +324,7 @@ to the 'GRUB_CMDLINE_LINUX_DEFAULT' variable:
 
 After that remember to
 xref:qm_pci_passthrough_update_initramfs[update the `initramfs`],
-xref:qm_pci_passthrough_update_grub[update grub] and
-reboot your host.
+and reboot your host.
 
 VM Configuration
 ^^^^^^^^^^^^^^^^
-- 
2.20.1