[pve-devel] [PATCH 1/5] RFC: Efficient VM backup for qemu

[Dietmar Maurer]

Signed-off-by: Dietmar Maurer <dietmar at proxmox.com>
---
 docs/backup-rfc.txt |   96 +++++++++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 96 insertions(+), 0 deletions(-)
 create mode 100644 docs/backup-rfc.txt

diff --git a/docs/backup-rfc.txt b/docs/backup-rfc.txt
new file mode 100644
index 0000000..8a32c38
--- /dev/null
+++ b/docs/backup-rfc.txt
@@ -0,0 +1,96 @@
+RFC: Efficient VM backup for qemu
+
+=Requirements=
+
+* Backup to a single archive file
+* Backup needs to contain all data to restore VM (full backup)
+* Do not depend on storage type or image format
+* Avoid use of temporary storage
+* store sparse images efficiently
+
+=Introduction=
+
+Most VM backup solutions use some kind of snapshot to get a consistent
+VM view at a specific point in time. For example, we previosly used
+LVM to create a snapshot of all used VM images, which are then copied
+into a tar file.
+
+That basically means that any data written during backup involve
+considerable overhead. For LVM we get the following steps:
+
+1.) read original data (VM write)
+2.) write original data into snapshot (VM write)
+3.) write new data (VM write)
+4.) read data from snapshot (backup)
+5.) write data from snapshot into tar file (backup)
+
+Another approch to backup VM images is to create a new qcow2 image
+which use the old image as base. During backup, writes are redirected
+to the new image, so the old image represents a 'snapshot'. After
+backup, data need to be copied back from new image into the old
+one (commit). So a simple write during backup triggers the following
+steps:
+
+1.) write new data to new image (VM write)
+2.) read data from old image (backup)
+3.) write data from old image into tar file (backup)
+
+4.) read data from new image (commit)
+5.) write data to old image (commit)
+
+This is in fact the same overhead as before. Other tools like qemu
+livebackup produces similar overhead (2 reads, 3 writes).
+
+=Make it more efficient=
+
+The be more efficient, we simply need to avoid unnecessary steps. The
+following steps are always required:
+
+1.) read old data before it gets overwritten
+2.) write that data into the backup archive
+3.) write new data (VM write)
+
+As you can see, this involves only one read, an two writes.
+
+To make that work, our backup archive need to be able to store image
+data 'out of order'. It is important to notice that this will not work
+with traditional archive formats like tar.
+
+During backup we simply intercept writes, then read existing data and
+store that directly into the archive. After that we can continue the
+write.
+
+==Advantages==
+
+* very good performance (1 read, 2 writes)
+* works on any storage type and image format.
+* avoid usage of temporary storage
+* we can define a new and simple archive format, which is able to
+  store sparse files efficiently.
+
+Note: Storing sparse files is a mess with existing archive
+formats. For example, tar requires information about holes at the
+beginning of the archive.
+
+==Disadvantages==
+
+* we need to define a new archive format
+
+Note: Most existing archive formats are optimized to store small files
+including file attributes. We simply do not need that for VM archives.
+
+* archive contains data 'out of order'
+
+If you want to access image data in sequential order, you need to
+re-order archive data. It would be possible to to that on the fly,
+using temporary files.
+
+Fortunaltey, a normal restore/extract works perfectly with 'out of
+order' data, because the target files are seekable.
+
+=Archive format requirements=
+
+The basic requirement for such new format is that we can store image
+date 'out of order'. It is also very likely that we have less than 256
+drives/images per VM. We also want to be able to store VM
+configuration files. 
-- 
1.7.2.5